Allpar Forums banner

Chrysler Stereo Pages at Allpar

20K views 0 replies 1 participant last post by  Allpar.com Content 
#1 · (Edited by Moderator)
Chrysler Stereo Pages at Allpar

Technology Electronic device


General Chrysler-related radio and stereo articles at Allpar:
CD and DVD systems (stereos have a three-letter code on the face plate)
Tape and tape/CD systems
From here to Infinity
CD changers
Classic systems (before tape decks)

Some 2010-2011 stereos used by Chrysler required firmware updates to avoid high power usage on standby, which could drain batteries. There have also been stability and feature-fixing firmware updates for 2011 stereos and navigation systems.

We asked Chrysler about SD card compatibility with their UConnect stereos; we had mixed success with various cards of various sizes. The rep said to get class 2, 4, or 6 cards (not class 10, which is faster), and that 8 gigabytes seemed to be the dividing line between consistent function and problems. This information came in October 2012; firmware updates and newer hardware might change those specs.

Replacing cassette and 8-track drive belts (by Jeremy Schrag)

First, you need to measure the width of the belt. Second, you need to find the internal circumference, and then adjust for belt stretch (these belts always stretch out over time, and you want to make sure your new belt is a little tighter than the one that just came off.)

Office ruler Ruler Measuring instrument Thermometer Slide rule


Lay the belt out as shown, next to a ruler, using two small screwdrivers, toothpicks, or other implements to take out the slack. Do not stretch the belt, just pull it out straight. Measure the length of one side, then multiply by two. Take the result and deduct 5-10% for belt stretch. Convert that internal circumference to inches, if needed, and order a new belt. In this example, I would go looking for a belt with a 15.4" or 15.5" internal circumference with a belt thickness of 0.39".

Chrysler and windshield radio antennas

Burton Bouwkamp wrote:

From 1968 to 1975, I was Director of Product Planning at Chrysler. During that time Styling (Elwood Engle) lobbied top management to put the antenna in the windshield á la GM. I objected because of the loss in radio performance.

I had a very simple test. My cottage in Mecosta was 160 miles from Detroit and my favorite Detroit radio station was WJR (J. P. McCarthy, Bud Guest, etc). I could get WJR with a mast antenna from the cottage but not with a windshield antenna. I was worried that if the customer experienced this loss in performance that he would blame the reduced radio reception in his new car on the quality of the radio.

Electronics Product Technology Electronic device Audio equipment


Finally in a showdown with Elwood I lost. Management made a compromise decision and that was to put the windshield antenna only on the Imperial - not across all car lines as Styling wanted.

The rest of the story is that after one year's field experience, the Chrysler/Imperial National Dealer Council formally recommended that we return to the fender mounted mast antenna. We did - but we built Imperials with windshield antennas for one or two years. (Eventually, GM also discarded the windshield antenna.)

Footnote: We (Engineering) were not happy with the fragile nature of the telescoping antenna so the Radio Lab (Frank Jenkins, Manager) came up with a fixed length stainless steel mast antenna which was rugged and provided good reception. I approved it. I can't remember the year that the stainless steel antenna entered production but it was when I was Director of Body Engineering (1979 - 1983).

Home
Engines
Reviews
Chrysler 1904-2018
Upcoming
Trucks
Cars

Spread the word via <!--Tweet or--> Facebook!

We make no guarantees regarding validity or accuracy of information, predictions, or advice - .
Copyright © VerticalScope Inc. All rights reserved. Dodge, Jeep, Chrysler, Ram, and Mopar are trademarks of Fiat Chrysler Automobiles.

 
See less See more
6
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top