Allpar Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 19 Results
  1. Repairs, Maintenance, Help
    Hi everybody, I’m looking to find a doner vehicle to pull a tranny from. Who knows what my best candidates are? I know the a-500/42re is barely enough and would consider beefing up to a 518 if not too difficult but with so many versions of the a500/a518 it’s been difficult to find a good doner...
  2. Repairs, Maintenance, Help
    I NEED HELP! My car runs horribly and I want to make it perfect again! I changed the cap rotor and the plugs and wires. I have also replace the alternator and voltage regulator. It is up and running very slow on the acceleration. Terrible gas mileage under 10 miles to the gallon. Somebody help!
  3. 2018-01-26.jpg

    Drove her home from Portland OR, took 9 gallons to cruise the 17 miles home. Knew what I wanted to do half way home...
  4. 1.4-1975_fthall-id_interior.jpg

    http://classicdartclassifieds.com/1975-sport-318-ft-hall-id/ this site still has it as an old listing and after reading-liars. Check it out...
  5. 1.3-1975_fthall-id_fender.jpg

    They banged that out and hid the antenna inside the fender-still in there and works for the stereo.
  6. 1.2-1975_fthall-id_engine.jpg

    It started life in Montana, and was an air-conditioned ride. Thats all gone, and what they did, we took a few steps farther and really did what we have on paper too
  7. 1.1-1975_fthall-id.jpg

    After we bought her I found these old pic's from a previous owner in Idaho. The list of "things"-not even close to what was really there, & the things done to her-were not. Was told this was not the vehicle I had bought. Funny, every Dart Sport must have the exact center windshield detail as mine?
  8. Repairs, Maintenance, Help
    Hi, I am rebuilding a 1968 318 (LA), the original Crankshaft is useable but is 0.30 oversized yet. I want to buy another one to have a spare, I saw in ebay a 500 bucks 1968 NOS, but other years are about the half of prize, I questioned the sales man about a 1973 318 Crankshaft but he said to me...
  9. Projects, Mods, Restoration
    Hi I bought a 1970 4 dr coronet 225 and floor shift 3 gears manual. I want to put a 318 engine and a 904 transmission. Is there any adapter to engine mounts or I have to change K member. 70 is a only year k-member or I can use from other years? And what could I need to put my 904 instead of...
  10. Projects, Mods, Restoration
    My truck, known by many names has been owned by me for a bit over a year total. I had it from late 2016 to 2017 when I traded it for a 89 GMC 1500 with a rebuilt engine and transmission that I ended up selling. I later ended up with a 93 f150 flareside, which was hit in the passengers side door...
  11. Projects, Mods, Restoration
    So, in a nutshell, though some dealing, I got a truck back I traded off in 2017, a 1984 Dodge D150 "Prospector". It smokes, but it runs good. I'm thinking of finding a good running donor engine and doing a swap (I have access to a junkyard) for something a bit better than what I have.My truck...
  12. Repairs, Maintenance, Help
    Hello all. First post on this forum. Spent about 2 hours trying to search for an answer on here but didn't get any results. The car, 1980 LaBaron, collector plates, 318 auto. Lean burn replaced by Chrysler dealer at some point, long before I got the car ten years ago. Carb is not original...
  13. Projects, Mods, Restoration
    I've got the Plymouth (1947 Business Coupe) and now the 318 (1998 Jeep Grand Cherokee). Now to get the 318 transplanted. I am comfortable with the physical installation. (Motor mounts, trans cross-member, etc.) What I would like to determine is how much of the stuff under the Jeep's hood do...
  14. Repairs, Maintenance, Help
    I have a 1974 dart sport with a 360. I am trying to replace the motor mounts but every time I order them from a place, they turn out to be bigger from the original mounts and dont fit. Has anyone else encountered this problem and does anyone have a solution or a reason why they are bigger...
  15. Current Motorsports / Racing News
    Hello, My name is Devin McCree, I'm 18 years of age and I have been racing for 10 years. After competing in 8 full seasons; I finished as runner up in 3 seasons, and as the champion in 2. I had to sit out last season due to a lack of funds. Currently, I'm attending Ventura College full time and...
  16. Performance
    I would like to mate a modern automatic transmission such as the 545RFE, 45RFE, or W5A580/NAG1 to a 1970 small block 318 from a Duster. I know PCS makes standalone controllers and harnesses for the NAG1 and 545RFE, but I am not sure what would be necessary to get this to work if it's even...
  17. Projects, Mods, Restoration
    ok first off motor and tranny is out of a 84 fifth avenue. 2barrel and all. the rearend is out of 89 dodge Dakota with v8. im going to double check my gear ratio tomorrow. but think its a 355 or 390. all this under a 52 dodge truck. im hoping the a904 is correct on transmission. looks like...
  18. Ram, Pickups, New Wagoneer, Commercial Trucks
    With the engine cover removed, a Loud Rattle is heard under light acceleration, the EGR is apparently working, needle moves, idles rough with the EGR solenoid disconnected etc., but rattle can't be heard at all with the engine cover installed, sounds fine then, what else is how probable with...
1-19 of 19 Results
Top